Sherwin-Williams Floorcoating Resupen WB Colour 5 Litres

Save £9.47
  • Coloured, Water-Based Polyurethane Seal
  • 5L Containers
  • Matte or Satin Finish
  • Two Pack
  • UV Stable
  • Resistant to Chemicals, Abrasion, Hot Water & Skydrol
  • Wide Colour Range Available

Colour: Black
Finish: Satin
Price:
Sale price£107.00ex vat Regular price£116.47ex vat

Resupen WB is a UV stable polyurethane finish for application onto concrete, plaster and wood or as a seal coat on Sherwin-Williams wall and flooring systems. Resupen WB is fast drying, abrasion resistant and offers excellent chemical resistance across a range of chemicals. Resupen WB can be used on both floors and walls to produce seamless hygienic surfaces.

Advantages

  • Excellent chemical resistance
  • No VOC’s
  • Skydrol & Hyjet resistant
  • UV Stable
  • Easy to clean
  • Resistant to hot water

Recommended Use

  • Laboratories
  • Automotive and aviation areas
  • Prisons and police cells
  • Medical and healthcare
  • Pharmaceutical areas
  • Food factories and beverage areas

Surface Preparation

New Concrete Floors:

New concrete must be clean, sound, dry, fully cured and surface laitance removed by vacuum enclosed shot blasting or mechanical grinding, a minimum strength of 25N/mm² is required.

Existing Concrete Floors:

Remove all dirt, oil, grease, old paint or any other surface contaminants by vacuum enclosed shot blasting, scarifying or mechanical grinding. Fats, oils or greases must be removed by mechanical means and detergent washing and making sure all residue of detergent is washed and removed by rinsing with clean water. Local repairs should be carried out using Resuscreed PA. If the old resin flooring cannot be removed then please consult with our technical team for advice on intercoat adhesion and suitability, as it may not be compatible with the existing floor coating.

Timber/Wooden Floors:

Must be clean, sound and dry. Old varnish/topcoat must be removed/sanded prior to application as it may interfere with the inter-coat adhesion with Resupen WB

NOTE: Care must be taken to ensure that surface preparation is thorough but does not disfigure the surface

Application:

Mixing: Mix the entire contents of the base with the hardener.
If a separate mixing bucket is being used mix thoroughly ensuring all contents of both components are removed from the buckets supplied. Mix using a high-speed electric mixer (for colours) or a slow-speed electric mixer (for clear) for approximately three to four minutes until the two components are fully combined. NOTE: The coloured product must be thoroughly mixed in order to achieve a smooth, creamy mixture. Once the hardener is added it will appear lumpy in consistency and mixing must continue until the mixture is smooth.
The mixed unit should be applied immediately by roller, brush or squeegee with a consistent procedure. Floor areas should be cross rolled to ensure even application and to minimise roller marks. It is important to maintain a wet edge with this product to minimise the risk of roller marks in the cured finish.

Application Conditions:

The ambient temperatures of the areas should not be allowed to fall below 15°C throughout the application and the curing period, as this could have an adverse effect on the appearance and colour of the system. The surface temperature must be above 10°C. Where possible it is recommended that the application area is heated to a minimum temperature of 15°C ideally to allow the ambient and substrate temperature to stabilise prior to the installation.
Up to 5% water may be added in warmer conditions to maintain the wet edge of the product during application. NOTE: Applied coating should be protected from moisture during application and during the curing period. Exposure to
moisture during this time can cause surface and colour variations.

Full product data sheets and safety data sheets are available on request.

Download Product Data Sheet (PDS_SW_Resupen-WB-Colour-Technical-Datasheet.pdf)

Payment & Security

American Express Apple Pay Diners Club Discover Google Pay Maestro Mastercard PayPal Shop Pay Visa

Your payment information is processed securely. We do not store credit card details nor have access to your credit card information.

You may also like

Recently viewed