- Coloured Solvent Based PU Coating
- Two Pack
- UV Stable
- Chemical & Thermal Shock Resistant
- Abrasion & Impact Resistant
- Hygienic & Easy to Clean
- Offers Flexibility
Resutile is a high performance, two-pack polyurethane floor coating which is designed to provide excellent chemical resistance and light fastness. It is a hard-wearing and tough but flexible coating with very good resistance to impact, abrasion and high temperature. Resutile is regularly used in the aviation industry due to its excellent resistance to Skydrol.
- Excellent chemical resistance
- UV stable
- Good abrasion and impact resistance
- Hygienic and easy to clean
- Excellent resistance to thermal shock
- Has a degree of flexibility
- Aircraft hangars
- Prisons and police cells
- Chemical plants
- Pharmaceutical areas
- Medical and Healthcare
- Anti-slip finishes can be created using a scatter of aggregate
New Concrete Floors:
New concrete must be clean, sound, dry and fully cured and surface laitance removed by vacuum enclosed shot blasting or mechanical grinding, a minimum strength of 25N/mm2 is required.
Timber Floors :
Must be clean, sound, dry. Old clear varnish/topcoat must be removed/sanded prior to application, as it may affect the inter-coat adhesion with Resutile.
Existing Concrete Floors:
Remove all dirt, oil, grease, old paints or any or other surface contaminants by vacuum enclosed shot blasting, scarifying or mechanical grinding. Fats, oils or greases must be removed by mechanical means and detergent washing. Local repairs should be carried out using Resuscreed PA or Resuscreed 45.
Existing Floors (previously coated):
All previous coatings and loose floor paints must be removed by mechanical preparation as described in the above section and primed as specified. if the old resin flooring cannot be removed, then please consult with our technical team for advice on inter-coat adhesion and suitability, as it may not be compatible with existing floor coating.
Where Resutile is applied to masonry/concrete surfaces, care must be taken to ensure that surface preparation is thorough but does not disfigure the surface.
Where surfaces are found to be porous a primer coat may be required to achieve a uniform sealed surface.
Resutile may be applied directly to concrete or as a seal coat or topcoat to a resin floor system specified in our datasheets where a primer is not required.
When applied directly to porous substrates the surface may require priming. Dry surfaces may be primed with Resuseal WB Clear or Resuprime ST.
Where the Relative Humidity of the substrate exceeds 75% Resuprime MVT should be specified and selected on the basis of hygrometer readings in
accordance with BS 8203. The number of coats to be applied is chosen in accordance with the following table.
ERH% Required Coating Thickness
75-85 1coat of RESUPRIME MVT at 200 microns per coat
85-92 2coats of RESUPRIME MVT at 200 microns per coat
92-97 3coats of RESUPRIME MVT at 200 microns per coat
The ambient temperatures of the area should not be allowed to fall below 10°c throughout application and curing. The surface temperature must be above 5°c.
Mixing: Pre-mix the base component to a uniform consistency then add the entire contents of the hardener to the base and mix by using a slow speed handheld powered mixer and mixing paddle for approximately two to three minutes to achieve a consistent mixture. Note: Do not use a separate mixing bucket as it may affect the mixing ratio.
Apply the whole mixed paint by using spreading rake, roller and brush to achieve the maximum coverage within the specified pot life time frame.
Do not add solvent to this product.
Slip resistance can be improved by lightly broadcasting anti-slip aggregates on the first coat (after primer) whilst still wet and back rolling, at a rate of 50/100 g/m2. When cured apply the second Resutile coat to secure the aggregates.
Full product data sheets and safety data sheets are available on request.
Payment & Security
Your payment information is processed securely. We do not store credit card details nor have access to your credit card information.